We use a solid carbide insert, ground to a special contour that does not leave the objectional belt mark on the case, common to ordinary carbide dies. With a carbide sizer, no case lube is needed, and you don't even have to clean your cases.

No need for a taper crimp die, plus better accuracy with Lee Dies. Taper crimp dies are used to correct the problems caused by the improper expanding plug design or adjustment. They distort the bullet shank and reduce accuracy. Because the Lee Expander flares the minimum amount, consistent with easy bullet insertion, all of the flare is removed with the bullet seating die, thus eliminating the need for a taper crimp die.

Includes:
* FULL LENGTH SIZER
* BULLET SEATER & ROLL CRIMPER
* FACTORY CRIMP DIE
* BUILT IN STUCK CASE REMOVER
* LONG GUIDED EXPANDER
* SHELL HOLDER
* POWDER DIPPER
* LOAD DATA AND INSTRUCTIONS

Best Internal Finish in the Industry
All Lee dies are machine honed to the smoothest possible finish. Don't confuse this with the surface polish used by most manufacturers. A polish simply makes a shiny surface. It's like trying to sand wood without backing under the sandpaper. The surface in Lee dies is progressively honed to a fine finish with no waves or ripples.

Compare to other brands costing twice as much and you'll recognize what a fantastic bargain they are. We offer these only to show that when you buy Lee Dies- without all the extras Lee customers have come to expect- the price is significantly lower, yet the quality is the best. Our tolerance is 50% less than the advertised amount of a popular and expensive brand. We guarantee these dies are better than any other brand. These dies are a Really Great Buy. They cost less, because like other die makers, we left out the extras which are included in our PaceSetter™ dies.

Lee Collet Series 2 Die Set includes most accurate neck sizer  NZ$88 (incl. GST)
NB: Please specify caliber in comment box on order form

Common Calibres are: (222, 223, 22/250, 243, 6.5x55, 270, 7mm/Mag, 7.62x39, 30-30, .308, .30-06, .303, 8mm please specify in comment box on order form)

Die set includes: Collet neck sizing die, dead length bullet seating die, shell holder, powder measure, charge table and storage box.
This set is designed for assembling the most accurate ammunition, but is not recommended for hunting rounds as the case is neck sized only and the bullet is not crimped in case.

Choose this die set for maximum versatility. The set features a full length-resizing die to return brass to factory new dimensions, perfect for reloading brass fired in other guns. The Collet Neck sizing die is used on your fire formed brass giving you best possible accuracy. No case lube required and cases last almost forever. The Easy Adjust Dead Length Bullet seating die foolproofs the bullet seating adjustment, and assures perfect seating depth every time. The Factory Crimp die provides a secure crimp on bullets with or without a crimp groove. In most cases it helps accuracy by providing a uniform higher start pressure and gives the finished cartridge Factory like accuracy and dependability.

Calibers Available:
223 Remington - # 90694
22-250 Remington - # 90739
243 Winchester - # 90556
6.5mm Creedmoor - # 90939
270 Winchester - # 90593
7mm Remington Magnum - # 90679
30-30 Winchester - # 90693
308 Winchester - # 90695
30-06 Springfield - # 90736
300 Winchester Magnum - # 90738

Lee Die Lock Rings (Universal - Set of Three) NZ$19 (incl. GST)

Lee Shell Holder for Autoprime/Hand Primer NZ$11 (incl. GST)
NB: Please specify caliber in comment box on order form

Lee Shell Holder for Press (Fits all Standard Presses) "R" Series NZ$14 (incl. GST)
NB: Please specify caliber in comment box on order form

* Model # 90600

The LeeBreech Lock system allows reloaders to quickly and easily change dies in seconds. Dies fit inside of the bushing, which allows them to be quickly installed and removed from the press leaving the die setting intact for the next reloading session. This saves valuable time setting up, and the hassle of resetting your dies during each reloading session.